RhinoPower Ltd

Bob · Bob

Is it possible to recover a H8/500 after a failed flash? From testing I believe the boot loader to be missing .

TechSupport · TechSupport

http://www.rhinopower.org/knock/knock.html

Mikey H · Mikey H

Good afternoon everyone. I have a Suzuki Jimmy that I have recently purchased knowing there was an issue with the vehicle. I was was told it was over heating when I bought it, but after further investigation I found it wasn't over heating but when it gets up to temperature it was misfiring as if it was run...

Bob · Bob

Hi I Am looking for help pulling the rom (for now) on what I believe to be a Mh6311 100 pin chip variant. If possible I’d like a data sheet . If none of the above is possible can I send a spare ecu to someone to have a try.? Pictures to follow. Thanks Bob.

rab · rab

I want to use it to fire up a fuel injector for flow tests. It clicks the injector once only and shuts it off. CEL never goes out and error code 41 flashes (no crank signal). Got ECT, AIT, throttle position potentiometer, MAF potentiometer, 13V battery power, square wave generator for Cam sensor set at...

Jinesh · Jinesh

HI I have design a KWP2000 protocol as Tester. Now I need to check its working. I found that in Celerio using Kline we can read VIN number (i.e. 0902) is it correct? please correct me if I am wrong

Heath · Heath

Has anyone gotten Rhinoview to run on a Raspberry Pi? My idea is to mount a Raspberry Pi under the dash, have it power up via the ignition and autorun the Rhinoview software with the video output to the in-car DVD player AUX input. Saves lugging a laptop about.

TechSupport · TechSupport

This is a project thats been in development for a while. The early MX5 ECUs use mostly the same chipset as the 57B Vitara ECUs and this daughterboard has been developed to allow them to be reprogrammed. The port expander is the same Mitsubishi one used for the Vitara 56B daughterboard.

Andrei_Eugen · Andrei_Eugen

Hi! I want to build a device that acts like an in-car organizer and mainly needs the car's mileage information at startup. Is there any way that this information can be made available via the OBD1 or OBD2 interface? Or is this info only available on the instrument cluster? I have a Suzuki Swift 2 (2010)....

TheZuke · TheZuke

http://www.rhinopower.org/Rhinoview/sdl_if/sdl_if.html

TechSupport · TechSupport

http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=KIT33812ECUEVME&fsrch=1&sr=3

TechSupport · TechSupport

http://www.rhinopower.org/scitsu/scitsu.html

Topic		Started By	Replies	Views	Last Post
	Bricked H8/500 ? (Preview) Is it possible to recover a H8/500 after a failed flash? From testing I believe the boot loader to be missing .	Bob	14	2171	Feb 23, 2022 by Bob
	Knock Sensor and Jaycar interface tests (Preview) http://www.rhinopower.org/knock/knock.html	TechSupport	4	3723	Feb 14, 2022 by TechSupport
	Suzuki Jimmy help (Preview) Good afternoon everyone. I have a Suzuki Jimmy that I have recently purchased knowing there was an issue with the vehicle. I was was told it was over heating when I bought it, but after further investigation I found it wasn't over heating but when it gets up to temperature it was misfiring as if it was run...	Mikey H	0	1111	Jan 26, 2021 by Mikey H
	Mitsubishi ecu help ? (Preview) Hi I Am looking for help pulling the rom (for now) on what I believe to be a Mh6311 100 pin chip variant. If possible I’d like a data sheet . If none of the above is possible can I send a spare ecu to someone to have a try.? Pictures to follow. Thanks Bob.	Bob	1	1462	Dec 28, 2019 by Bob
	Trying to run a spare 1995 Tracker/Suzuki ECU on my kitchen table (Preview) I want to use it to fire up a fuel injector for flow tests. It clicks the injector once only and shuts it off. CEL never goes out and error code 41 flashes (no crank signal). Got ECT, AIT, throttle position potentiometer, MAF potentiometer, 13V battery power, square wave generator for Cam sensor set at...	rab	13	2459	May 25, 2018 by rab
	Need to read VIN from Celerio (Preview) HI I have design a KWP2000 protocol as Tester. Now I need to check its working. I found that in Celerio using Kline we can read VIN number (i.e. 0902) is it correct? please correct me if I am wrong	Jinesh	0	2057	Apr 11, 2017 by Jinesh
	Rhino on Raspberry (Preview) Has anyone gotten Rhinoview to run on a Raspberry Pi? My idea is to mount a Raspberry Pi under the dash, have it power up via the ignition and autorun the Rhinoview software with the video output to the in-car DVD player AUX input. Saves lugging a laptop about.	Heath	6	3419	Nov 8, 2016 by TechSupport
	MX5 daughterboard (Preview) This is a project thats been in development for a while. The early MX5 ECUs use mostly the same chipset as the 57B Vitara ECUs and this daughterboard has been developed to allow them to be reprogrammed. The port expander is the same Mitsubishi one used for the Vitara 56B daughterboard.	TechSupport	4	4677	Feb 22, 2015 by TechSupport
	Vehicle Information Project (Preview) Hi! I want to build a device that acts like an in-car organizer and mainly needs the car's mileage information at startup. Is there any way that this information can be made available via the OBD1 or OBD2 interface? Or is this info only available on the instrument cluster? I have a Suzuki Swift 2 (2010)....	Andrei_Eugen	4	2783	Jan 17, 2014 by TechSupport
	Rhinopower web site... (Preview) http://www.rhinopower.org/Rhinoview/sdl_if/sdl_if.html	TheZuke	0	3480	Feb 17, 2011 by TheZuke
	Freescale - ECU Reference design (Preview) http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=KIT33812ECUEVME&fsrch=1&sr=3	TechSupport	0	4716	Oct 29, 2010 by TechSupport
	Scitsu Revcounter (Preview) http://www.rhinopower.org/scitsu/scitsu.html	TechSupport	0	2968	Sep 13, 2010 by TechSupport
Page 1 of 1 sorted by