RhinoPower Ltd

Members Login
Username 
 
Password 
    Remember Me  
RhinoPower EFI -> RhinoPower Forum -> RhinoView Diagnostic Software -> Connection Issues - JDM 1997 JB32W
Post Info TOPIC: Connection Issues - JDM 1997 JB32W
Daisy


Newbie

Status: Offline
Posts: 1
Date:
RE: Connection Issues - JDM 1997 JB32W
Permalink  
 

I know I'm very late to the party, but had a similar connection issue. When downloading RV 1.4, Windows tried to protect me and leave all the files blocked. The results was just Rx Errors. For me, the solution was to right click on the zip file, select 'Unblock', then extract. Otherwise you'll have to unblock each file individually. After doing this, I was able to successfully connect and see the engine data.



__________________
Ian


Member

Status: Offline
Posts: 5
Date:
Permalink  
 

It's a brand new battery reading 12V. I think you're right about an issue with a bad connection. Fortunately, my mechanic was able to do some work on the engine and the CEL went away but I will inspect ground points and wiring. Thanks for all your patience and assistance.



__________________
TechSupport


Guru

Status: Offline
Posts: 1360
Date:
Permalink  
 

That could be a bad connection somewhere, do you get the same reading if you put the meter directly across the battery?



__________________

1984 Suzuki SJ413K pick up, 1.6 16V Baleno engine
2000 Suzuki Vitara 1.6 8V, many mods
2004 Suzuki Ignis 1.5VVT 4Grip
2006 Suzuki Jimny 1.3VVT JLX+
and many more.
Ian


Member

Status: Offline
Posts: 5
Date:
Permalink  
 

Had to get my hands on a multimeter. Looks like I'm getting only 8V across the 2 bottom pins. Is this insufficient? Any ideas on what may cause this? Bad fuse/ground?



__________________
TechSupport


Guru

Status: Offline
Posts: 1360
Date:
Permalink  
 

That is correct, have you got 12V across the bottom two pins?

__________________

1984 Suzuki SJ413K pick up, 1.6 16V Baleno engine
2000 Suzuki Vitara 1.6 8V, many mods
2004 Suzuki Ignis 1.5VVT 4Grip
2006 Suzuki Jimny 1.3VVT JLX+
and many more.
Ian


Member

Status: Offline
Posts: 5
Date:
Permalink  
 

Pin 7 is not populated. 

 

Looks like only pin 5, 18 and maybe 12 are populated. Thanks!



Attachments
__________________
TechSupport


Guru

Status: Offline
Posts: 1360
Date:
Permalink  
 

Can you confirm that the diagnostic connector does not have pin 7 populated?

__________________

1984 Suzuki SJ413K pick up, 1.6 16V Baleno engine
2000 Suzuki Vitara 1.6 8V, many mods
2004 Suzuki Ignis 1.5VVT 4Grip
2006 Suzuki Jimny 1.3VVT JLX+
and many more.
Ian


Member

Status: Offline
Posts: 5
Date:
Permalink  
 

Thanks for the quick response. 

Switched to 15625 and restarted. No change at all.

If it helps, the sticker on the ECU says:

1 -4V MT

33920-81CA 1

112000-3781

12V



__________________
TechSupport


Guru

Status: Offline
Posts: 1360
Date:
Permalink  
 

Hello Ian
Please try changing the setting to 15625 and then restart the application.

__________________

1984 Suzuki SJ413K pick up, 1.6 16V Baleno engine
2000 Suzuki Vitara 1.6 8V, many mods
2004 Suzuki Ignis 1.5VVT 4Grip
2006 Suzuki Jimny 1.3VVT JLX+
and many more.
Ian


Member

Status: Offline
Posts: 5
Date:
Permalink  
 

Hi everyone,

I have a JDM 1997 JB32 Jimny Sierra with a G13BB engine and cannot connect to the tool. I have followed the instructions to install the required drivers and steps to connect the device to the computer. Baud rate is set to 7812. 

I am receiving RX error messages in the Bad Data count section. Can someone advise how to fix?

 



__________________
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.
RhinoPower EFI -> RhinoPower Forum -> RhinoView Diagnostic Software -> Connection Issues - JDM 1997 JB32W


Create your own FREE Forum
Report Abuse 		Powered by ActiveBoard